Record and reduce your energy costs and increase your sustainability with the VA 550. Monitor your Consumption and analyse your leakage flows with just one measuring device. Due to its design, it is also ideal for Portable Measuring.

The innovative VA 525 combines modern digital interfaces for connection to an energy monitoring system with a small, compact design. The VA 525 is always used when many machines (compressed air consumers) have to be integrated into an energy monitoring network.

Reduce your energy costs and increase your sustainability with the VA 525 compact sensor. Monitor the consumption of individual machines and analyze your leakage flows with just one measuring device.

Reduce your energy costs and increase your efficiency with the VD 500. Suitable directly for measurement after the compressor. Monitor the delivery rate of your compressor and create a FAD analysis.

• Measurement immediately downstream of the compressor

• Measurement at high temperatures

• Ready-to-use compact design to minimise installation effort - therefore no volume corrector required

• Provides Flow, Total consumption, Temperature and Pressure

• Differential pressure sensor element with unique sensitivity, measures highly accurately at < 2 m/s

• Large flow measuring range with extended measuring span thanks to the use of measuring sections with a reduced inner diameter

• Smaller inlet sections due to the use of an averaging pitot tube

• Robust design, no moving parts

• Sensor head can be removed for calibration

The high-precision all-rounder. Record and reduce your consumption and increase your sustainability with the VX 570. Monitor your consumption of a wide range of media with just one sensor.

• Precise measurement from 2 m/s

• Suitable for unknown or changing gas compositions and mixed gases

• Usable for liquids and steam

• Rough industrial applications can be realized due to robust aluminum housing

• Measures actual volume flow and mass flow

• Measurement of the standarized volume flow by integrated pressure and temperature measurement

• The innovative measuring principle guarantees precise flow measurement in different media

• Suitable for fast changing temperature and pressure changes as well as large mass flows

• No moving parts, therefore low maintenance

• Corrosion resistant - all parts in contact with media made of stainless steel

• Insensitive to vibrations due to reference vibration measurement

With the FA 500 you make the right choice for highest precision in dew point measurements. Our sensor offers a wide span of measuring ranges perfectly matched to the needs of different compressed air dryers. Rely on us for accurate results in any situation.

Monitoring a compressed air dryer is critical to increase energy efficiency, ensure product quality, prevent machine damage, identify maintenance needs and achieve cost savings. This contributes to the smooth operation of compressed air systems in various industrial applications.

• Multiple display pages to show dew point and other measured values such as relative humidity and temperature 

• Definition of threshold values for the alarm relay, definition of hysteresis

• Scaling of the analog output 04...20 mA and switching to other measured variables

• Input of system pressure as well as reference pressure for calculation of reference dew points, e.g., atmospheric dew point

The UltraCam LD 500/510 uses 30 MEMS microphones for the Calculation and visualisation of the ultrasonic image. In addition, the device makes inaudible ultrasound audible, even in noisy environments during production.

• shows you on the screen where the Leak is located

• Leak detection possible during production without interrupting system operation

• Very intuitive and no training required!

• 5 LEDs and ambient light sensor for intelligent lighting in dark environments

• Function for estimating Leakages (l/min or cfm) and (cost per year)

• Running time > 6 h with continuous operation

• The lightest acoustic camera on the market at 600 g

• Can be connected to existing LD 500/510

From recording of the measured data, indication on a big colour screen, alerting, storage up to remote read-out via webserver... this is all possible with DS 500. By means of the CS Soft Basic software alarms can be sent via SMS or e-mail. All measured values, measured curves and threshold exceedings are indicated. The curve progressions from the beginning of the measurement can be viewed by an easy slide of the finger. Daily/weekly/monthly reports with costs in € and counter reading in m³ for each consumption sensor are completing the sophisticated system concept. The big difference to odinary paperless chart recorders reveals in the easy initiation and in the evaluation of the measured data. All sensors are identified directly and powered by DS 500. Everything is matched and tuned.

IAC 500– Measures ambient conditions in the room – absolute pressure, room temperature, humidity.

• Monitoring the intake air of compressed air stations

• Monitoring of room air e.g. cold rooms, storage rooms or clean rooms

The delivery rate of compressors depends on the intake air.

The installation site and the climatic conditions must already be taken into account when designing compressed air stations.

Large temperature fluctuations, e.g. between day and night, lead to uneven compressed air flow.

The monitoring system for high-precision measuring of the Vaporous Residual oil content of Compressed air and Nitrogen.

"Forced Pressure Variation" for Long-term stable measurement results - auto-calibration:

Using the innovative "Forced Pressure Variation" measuring method, the OIL CHECK 500 generates internal reference gas in different mass concentrations. This CS INSTRUMENTS-protected process can be used to compensate for ageing or contamination-related components in the measurement signal, in particular long-term drift. No wearing parts such as activated carbon filters are required for the generation of zero air. The result is Low maintenance and Long-term stable Measuring.

Service friendly, no downtime:

The sensor unit can be replaced by the customer on site. This eliminates the need to return the entire device for recalibration.